Fair Lawn NJ Furnace and Air Conditioning Repair Installation Service

Arrived on site for driving cleaning. Customer led me to the event outside on the left side of the house. Use portable cable compressor to clean out the dryer vent from the outside. Ask customer to run the dryer inside. Fed hose down the vent and waited for the compressor to build up pressure. Took out a great amount of that was restriction the dryer vent. Went inside the event about 4 to 5 times with the hose to ensure cleanliness of the dryer vent. After cleaning dryer vent picked up all the link off the ground, cleaning up the best to the ability.

All right on site for maintenance. Customer led me to the basement where the air handlers located. Customer turned on the unit and saw the unit fully functional. Took out the old filtering replacing with a filter that was applied on site. Open up the evaporator code to check out the mirroring device in the condition of the evaporator coil. The main device is a piston and evaporator cause rain good condition. Also inserted two condensate treatment pills inside the condensate tray. I made sure that the water pump of the air handler was fully functional. Went outside pull the disconnect of the condenser to work on it safely and took out the top. Wash down the unit with chemical and water. Put the condenser back together and turn on the condenser and it turned on normally. Check the pressures with the field pieces. High pressure was a little low but it was 69 outside.

Arrived onsite for no cooling call. Condenser fan motor failed. Homeowner looking to replace system. Installed condenser fan motor. System still running hot. Misters had been added to the condenser that are helping

Arrived onsite for no cooling service call. Customer explained the breaker keeps tripping. Performed diagnostic. Removed compressor from the circuit and fan worked. Tested compressor wires for resistance measure a jumping ohm up to 300. Measures resistance to ground. Took top off and measure resistance on compressor leads. Again had high resistance measurement between leads. Measured resistance to ground in all 3 terminals. The compressor is confirmed grounded. Left plug off compressor. Returned disconnect in off position. Proving for replacement is being worked up.

Arrived on site for no Cooling. Customer turned on the unit when I arrived, the condenser outside was humming loudly. Sound like the the compressor was working but the fan was not spinning. Unplug the disconnect and open up the wiring for the condenser. Check for voltage and amps everything was fine checked out the capacitor that was pretty rusted up on the top but it was fine. Every component was working good except for the fan. Notice that the fan has a thermal protection, rang up the hose and tried calling it down for about 5 minutes with water.

Arrived on site for no Cooling. Customer turned on the unit when I arrived, the condenser outside was humming loudly. Sound like the the compressor was working but the fan was not spinning. Unplug the disconnect and open up the wiring for the condenser. Check for voltage and amps everything was fine checked out the capacitor that was pretty rusted up on the top but it was fine. Every component was working good except for the fan. Notice that the fan has a thermal protection, rang up the hose and tried calling it down for about 5 minutes with water. At the cooling down the condenser turned on the connector by plugging in the disconnect and the unit turned on very loudly. Check for pressures and pressures were pretty low super heat was higher than 50 and what temperature difference inside the house Peak at four degrees difference.

UV Light Air Purification Installation: Installed a UV-C germicidal light system inside the HVAC air handler to neutralize airborne pathogens. Connected the unit to the blower control circuit, ensuring it operated only during air circulation, and verified UV output for indoor air quality improvement.

Arrived onsite for ac maintenance on 1 system. Homeowner mentioned noise from indoor blower fan. Could not recreate the noise. System worked well while there. . Checked all electrical. Chemically Cleaned outside coil. measured pressures for 410a at 120/245psi with 5 degree sub cooling with outside temperature at 81 degrees. Measured temperature drop at 17 degrees. Cleaned out condensate line. Removed 20x20x1 filter located in air handler. Installed 2 -14x28x1 filters in filter grill provided by the homeowner System running as it should.

Arrived on site for maintenance. No one was in the building. Someone left unit running, started outside. Washed down condenser. Checked pressures of condenser,

Arrived onsite for no cooling call. Performed diagnostic on the system. Found a fault in the voltage enhancement system. Inspected motors and they seem to be in working order. Performed gold repair for the voltage enhancement system. System running as it should. Measured 30 degree temperature drop. Did not observe strange noises. Pressure within line of manufacturer’s settings. Confirmed filter is in good shape.

customer experiencing unit slowing down and not cooling well it is around 15 years old and so is the furnace. He is interested in replacing, well aware that may be a possibility.

Received a call at the AC system was not operating, upon arrival I found that the unit was running but low on refrigerant. It is an older R22 system and I do not recommend leak testing at this time. Added 3 lb of R22 refrigerant and the unit is now operating and cooling properly.

Arrived on site for no cooling call. Condenser fan was running. Air handler was running Compressor was off. Checked/tested capacitor. Capacitor was dead. Replaced capacitor. Compressor and condenser was fully operational. Updated customer. Customer acknowledged and signed off.

Heating System Repair: Diagnosed a cracked heat exchanger that posed a safety hazard. Removed and installed a new exchanger, ensuring proper combustion and restoring safe, efficient heat output.

UV bulb replacement.

Seasonal maintenance for (1) split system up to 5 ton cooling capacity, either roof or ground mounted Includes replacing of standard fiberglass air filter (pleated higher performance filters can be added at an additional cost) , includes replacing blower belt (if applicable), grease or oil bearings, chemically clean the condensing unit, clean the condensate drain line, check operation of all safety devices, check operation of operating controls, check all motors, compressor and refrigerant charge, visual inspection of the duct system. With a Comfort Club service you will also receive the added benefits of a 10% discount on repairs and diagnostic fees, service within 48 hours of placing the call and a water heater flush

Arrived onsite for ac maintenance on 1 units. Asked customer to turn AC on to confirm operation. Checked all electrical. Chemically Cleaned outside unit, measured pressures for 410a at 125/265psi with 10 degree sub cooling with outside temperature at 72 degrees. Measured temperature drop at 20 degrees. Cleaned condensate line. changed 20x30x1 filter. Performed efficiency test utilizing MeasureQuick. System running as it should.

HVAC Repair: Upgraded an outdated thermostat with a modern programmable unit, allowing for better temperature scheduling and improved energy management.

Arrived onsite for ac maintenance on 1 units. Asked customer to turn AC on to confirm operation. Checked all electrical. Chemically Cleaned outside unit, removed debris, cleared drainage holes. Observed a rusting in the outside condenser, measured pressures for R22 at 48/120psi with 17 degree sub cooling with outside temperature at 60degrees. Observed the suction line icing up. Cleaned evaporator coil and blew out condensate line. Observed significant rusting on the evaporator coil. Observed more icing on the inside coil. Recommend upgrading the system based on age and condition of the system.

Arrived onsite for ac maintenance on 1 units. Asked customer to turn AC on to confirm operation. Homeowner will changed filter in ceiling. No longer using 213 filter media. Checked all electrical. Chemically Cleaned outside unit removed debris and VMware’s drainage holes. measured pressures for 410a at 111/206psi with 10degree sub cooling with outside temperature at 60 degrees. Measured temperature drop at 18.5 degrees. Cleaned evaporator coil and cleared condensate line. System running as it should.

Arrived onsite for ac maintenance on 1 system. Turn AC on to confirm operation. Checked all electrical. Removed condenser top and clear debris. Chemically Cleaned outside coils and cleared drain holes, measured pressures for R407c at 47/101psi with 1.4 degree sub cooling with outside temperature at 48 degrees. Measured temperature drop at 21 degrees. Cleaned evaporator coil and condensate line. Changed 213 media filter provided by Climate Plus. System running as it should.

HVAC Repairs: Upon inspecting a client’s HVAC system, I discovered damaged insulation on the electrical wiring, posing both safety and performance concerns. I promptly replaced the compromised insulation to restore safe and efficient system operation.

Removed old boiler installed new crown velocity boiler. Installed four new zones plus an indirect tank was existing. Piped in indirect tank the proper way on auxiliary. Installed magna clean, expansion tank, spiral vent, Purge setup, with three separate circulator pumps. Pumps also included four zone valves. Everything is isolated and operating at this time. Ran 2-in PVC outside vented proper distances from Windows and doors.

Arrived onsite for heating maintenance 2 gas fired furnaces 1 in basement and 1 in the attic. Attic Furnace System: Turn heat on and confirmed operation. Changed 14x24x1 filter provided by customer. Brushed and Wiped down furnance blower cabinet and gas burners. Burners fired and are in good working order. No visual impingement detected. Checked electrical. Cleaned the flame sensor.. Measure temperature rise at 42 degrees. Performed Combustion Test. System is operating as it should. Discuss replacement of basement system as it is near 20 years and has used over 95% of its life expectancy. Homeowner would like to wait a couple more years.

Arrived onsite for maintenance on 4 systems. Performed inspection of the performance, mechanical, and safety systems. Started in suite 202. Confirmed operation of all systems. Cleaned washable filters on 3 mini split cassettes. Changed 20x20x1 ceiling filter. Measured temperature drop of 20 degrees on the big unit. 23 degrees in the small unit. 17 degrees on the ceiling split system.